Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for Knoxville Homeowners
When a driveway gate stops partway open or an operator clicks but won’t move the arm, the problem rarely fixes itself. A gate stuck open leaves your property exposed, and one stuck closed cuts off vehicle access entirely. We handle both, and we work on the brand already bolted to your gate rather than talking you into a replacement you don’t need.
Our technicians have up to experience on swing and slide gates, from residential Mighty Mule and LiftMaster openers to commercial FAAC and BFT systems. We answer 24/7, and fast dispatch from 7am to 7pm gets a technician to most Knoxville addresses same-day. Estimates are free, and you’ll know the price before any work begins. Call (866) 361-6964.
Understanding the difference between a mechanical failure and a control-board problem saves you money, and it’s the first thing we sort out on site. Whether your gate is fabricated steel, wrought iron, or cedar, our gate repair Knoxville service covers the hardware, the operator, and the wiring that ties them together.
Driveway Gate Repair
Driveway Gate Repair covers the full system at your entrance: the gate leaf itself, hinges and rollers, the operator arm or slide motor, and the safety devices that keep it from closing on a vehicle. You need it when the gate drifts, reverses halfway, or won’t respond to the remote at all. We diagnose the whole chain rather than swapping parts until something works, and our technicians have up to experience across residential and commercial operators.
Typical driveway gate repair in Knoxville runs $150 to $650 depending on whether the fix is mechanical, electrical, or both. Hinge and roller work sits at the low end; operator and control-board repairs climb higher. The written estimate sets the final price, and we agree it with you before we start.
Hinge and Roller Wear
Sagging gate leaves almost always trace back to worn hinges, bent rollers, or a post that has shifted in the ground. We check the post footing first, because rehanging a leaf on a loose post just moves the problem. Once the mounting is sound, new hardware restores smooth travel.
Operator and Arm Failures
An arm that jerks, stalls, or reverses without obstruction usually points to a failing operator or a misread limit switch. We test the motor under load and check the control board for heat damage. If the unit is repairable, we repair it; replacement is a conversation, not a default.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Welding
Gate Welding restores the structural joints that hold a gate square: hinge plates, frame corners, bottom rails, and post brackets. You need it when a weld has cracked, a hinge has torn free, or a gate has started to sag because a joint gave way. We reweld on site where the joint allows, and we tell you honestly when a section needs to come out and be rebuilt instead.
Metal gate repair with welding in Knoxville typically runs $200 to $550 depending on the number of joints and whether the gate has to be removed. Structural cracks that affect the frame cost more than a single hinge plate. The estimate is written and free, and the price is set before any torch is lit.
Cracked Frame Joints
A cracked corner weld lets the whole leaf twist, which then wears the hinges and throws the operator out of alignment. We grind out the old weld, re-fit the joint, and weld it properly rather than laying a cosmetic bead over the crack. Square and plumb come before anything else.
Hinge and Post Brackets
Hinge plates take the most stress on any swing gate, and post brackets take the most on slide gates. When they tear, the gate drops and starts dragging. We rebuild the bracket, check the anchor into the post, and confirm the gate swings freely before we call it done.
Commercial Gate Repair
Commercial Gate Repair keeps access-controlled entries working for tenants, deliveries, and staff, and it covers the same hardware as residential work plus the systems that manage it. You need it when a loop detector stops sensing a vehicle, a keypad or card reader loses communication, or an operator fails during peak traffic. We work on DoorKing and FAAC access systems as well as the operators behind them, so a single call covers the gate and the entry control.
Commercial gate repair in Knoxville usually runs $250 to $900 depending on whether the fault is in the operator, the detection loop, or the access hardware. Multi-lane properties and gates with integrated entry systems sit at the top of that range. We quote in writing and agree the price before work starts.
Loop Detectors and Safety Devices
A gate that closes on a vehicle usually has a failed induction loop or a misaligned photo-eye, not a broken motor. We test the loop with a meter, check the splice at the pavement edge, and confirm the safety edge reports correctly. Safety devices get fixed first, because a gate that ignores them is a liability.
Access Control and Keypads
When a keypad or card reader stops granting entry, the fault is often in the wiring between the reader and the operator board rather than the reader itself. We trace the circuit, test the relay, and confirm the gate cycles correctly from every entry point. Property managers get one point of contact for the whole system.
Iron Gate Repair
Iron Gate Repair addresses the movement and alignment problems that show up as a gate ages: sagging leaves, worn pivots, dragging bottoms, and operators that strain against a gate that no longer swings true. You need it when the gate scrapes the ground, binds halfway, or needs a push to close. We work the mechanical side and the operator together, since a misaligned gate will wear out a new motor quickly.
Iron gate repair in Knoxville typically runs $180 to $500 depending on whether the fix is pivot hardware, post anchoring, or operator realignment. Gates with a shifted footing cost more, because the post has to be reset before anything else holds. Our gate repair team quotes in writing and settles the price with you before work starts.
Sagging Leaves and Pivots
Iron gates sag at the pivot first, and the sag compounds every season as the hardware wears. We check the pivot pin, the bearing, and the post anchor as one assembly. Repairing all three at once costs less than chasing the sag year after year.
Rust and Joint Failures
Rust at a weld or a hollow section weakens the joint from the inside, and the gate starts to flex where it used to be rigid. We clean the affected area, assess how much metal is left, and repair the section properly. Cosmetic patching over structural rust is a waste of money.
Sliding Gate Repair
Sliding Gate Repair covers the track, the rollers, the guide posts, and the slide operator that drives the leaf. You need it when the gate jumps the track, drags on the ground, or stops short of its limit. A slide gate that comes off the track is a genuine safety hazard, because the leaf is heavy and can fall, so stop using it and get it looked at.
Sliding gate repair in Knoxville usually runs $200 to $600 depending on whether the track is worn, a roller has collapsed, or the operator needs work. Track replacement and footing repair push toward the higher end. We also handle the power feed and the safety edges on automated slides, so the gate stops for obstructions the way it should.
Track and Roller Alignment
Most slide gate problems start with a track that has settled or filled with grit, which then destroys the rollers. We clear and level the track, replace collapsed rollers, and confirm the leaf runs straight through its full travel. A gate that tracks true lasts far longer between repairs.
Slide Operators and Limits
When a slide operator stops short or overshoots, the limit switches or the encoder are usually out of adjustment. We recalibrate the travel, test the reverse function, and check the motor under load. If the board is failing, we repair or replace it rather than leaving you with a gate that half-works.
Wrought Iron Gate Repair
Wrought Iron Gate Repair handles the ornamental gates where appearance matters as much as function, so the fix has to restore both. You need it when a picket is bent, a scroll has cracked, a hinge has pulled loose, or the gate no longer lines up with the fence. We repair the structure and match the finish so the repair doesn’t stand out.
Wrought iron gate repair in Knoxville typically runs $180 to $480 depending on the extent of the metalwork and how much refinishing is needed. Bent pickets and single hinge repairs sit at the low end; a section rebuild with touch-up paint costs more. We measure the gate, quote in writing, and agree the price before any work starts.
Bent Pickets and Scrolls
A bent picket usually means something hit the gate, and the impact often cracks the joint where the picket meets the rail. We straighten or replace the section, then reweld and dress the joint. The goal is a repair that reads as original work.
Finish and Touch-Up
Bare metal left after a repair rusts within a season, so we prime and topcoat every welded area as part of the job. If the existing finish is failing across the gate, we tell you what a spot repair will and won’t hide. Honest expectations save callbacks.
Metal Gate Repair
Metal Gate Repair covers the fabricated steel and aluminum gates that make up most automatic entrances, and it’s the catch-all for anything the other categories don’t quite fit. You need it when the frame is bent, a panel is loose, a post has moved, or the gate has stopped sitting square. We assess the metal, the hardware, and the operator as one system.
Metal gate repair in Knoxville generally runs $150 to $550 depending on whether the work is hardware, structural, or both. Aluminum gates with loose panels and steel gates with bent frames both come up often. Our technicians have up to experience across these materials, and the written estimate sets the price before work begins.
Bent Frames and Panels
A bent frame throws the gate out of alignment and puts stress on the operator, so it has to be corrected before anything else. We straighten or replace the affected section and re-check the square. Loose panels get re-secured at the same time to stop rattling and further wear.
Foundation and Post Issues
A gate anchored to a loose post will never stay aligned, no matter how many times the hinges are adjusted. We check the post for movement and reset the footing if needed. Getting the anchor right is the foundation of every lasting repair.
Wood Gate Repair
Wood Gate Repair deals with the gates that move with the seasons, because wood swells in humid weather and shrinks when it dries, and that motion opens gaps and loosens hardware. You need it when a hinge has pulled out, a board has rotted at the bottom, or the gate has started to sag in the frame. We repair the structure and replace the failed sections.
Wood gate repair in Knoxville typically runs $150 to $450 depending on whether the work is hardware, board replacement, or frame bracing. Rot at the bottom rail is the most common issue, and it’s also the most important to catch early. We quote the repair in writing and agree the price before we start.
Rot and Board Replacement
Rot usually starts where the board meets the ground or a horizontal rail, and it spreads faster than it looks. We check the frame for soft spots, replace the affected boards, and treat the new wood. Catching rot early is cheaper than rebuilding the gate.
Hinge Pullout and Bracing
Wood hinges pull out because the screws lose their bite in the grain, not because the hinge is faulty. We fill and reinforce the mounting area or add a backing plate, then rehang the gate. Diagonal bracing keeps the frame square and stops the sag from coming back.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service LiftMaster equipment and know where it wears out first, from the operator arm on a residential swing gate to the control board on a heavier slide unit. We also work on FAAC and BFT systems, which show up on commercial and multi-access properties where the operator takes a lot of cycles. When a control board or a loop detector fails, we handle the diagnosis and the repair rather than sending it elsewhere.
On the residential side, we service Mighty Mule and Ghost Controls openers that homeowners often install themselves, and we’re honest about when a repair makes sense versus a swap. Linear, Viking, DoorKing, and Elite systems round out the coverage, including the access hardware that ties into them. Our technicians have up to experience across these platforms, and the recommendation follows what the system actually needs rather than what happens to be on hand. Whether you have a LiftMaster or any other make, we can help.
If you need a new system rather than a repair, our gate installation service covers the full measure, order, and setup, and you never have to coordinate a separate installer and repair tech.
Signs You Need a Pro Right Now
- The gate reverses or stops for no reason. This usually means the safety devices or limit switches are misreporting, and it will get worse under daily use. A gate that reverses on a vehicle is an injury risk, so stop using it and get it checked.
- The gate drags, sags, or scrapes the ground. A sagging leaf strains the operator and wears the hinges faster. Left alone, it can drop off a track or a pivot entirely.
- The operator clicks but the gate doesn’t move. A click with no movement points to a control board, a capacitor, or a dead motor. It’s rarely a remote problem, and it won’t fix itself.
- The gate is stuck open. An open gate is a security gap, and on a commercial property it’s also an access-control failure. This is the case to call on right away.
- You see sparks, smell burning, or find damaged wiring. Stop using the gate and keep clear of the operator. Electrical faults on a gate operator are dangerous, and they need a trained technician, not a DIY fix.
Our Process, Step by Step
- 1
You call and describe the gate. We ask for the brand, whether it’s a swing or slide, and what it’s doing. That tells us what to bring and whether it’s likely a same-day repair. Call (866) 361-6964 and we answer 24/7.
- 2
We come out and diagnose the whole system. We test the operator, the control board, the safety devices, and the mechanical travel with a meter and a load test. We don’t guess at a part before we’ve confirmed the fault.
- 3
You get a written estimate. We explain what’s wrong, what the repair involves, and what it costs, and we agree the price with you before any work starts. No work begins on a number you haven’t approved.
- 4
We do the repair. Mechanical, electrical, and welding work happen on site where the job allows. We test the gate through full cycles and confirm the safety devices report correctly before we leave.
- 5
We walk you through it. You get a clear account of what was fixed and what to watch for. If the system has a pattern of failure, we tell you what a longer-term fix would cost.
How Much Does Gate Repair Cost in Knoxville?
Gate repair in Knoxville typically runs $150 to $900 depending on the type of gate and what’s actually failing. A typical hinge or roller repair runs $150 to $350 depending on gate size and hardware. An operator or control-board repair runs $250 to $650 depending on the brand and whether the board is repairable. Commercial gate repair and access-control work runs $250 to $900 depending on the system. Sliding gate track and operator work runs $200 to $600. Welding and structural metal repair runs $200 to $550, and wood gate repair runs $150 to $450.
What affects the price most is where the fault sits. Mechanical fixes are usually straightforward; electrical and control-board work take longer to diagnose and often cost more in parts. A gate with a shifted post or a poor footing adds cost because the anchor has to be corrected first. A slide gate that has jumped the track may need roller and track work together, which pushes toward the higher end.
How you avoid overpaying: get the diagnosis in writing, ask whether the operator is repairable before agreeing to a replacement, and confirm the safety devices are included in the quote. Every estimate we give is free and written, and the price is set per job and agreed before work starts, so the invoice matches the quote.
Our Service Area Near Knoxville
We dispatch across Knoxville and the surrounding communities, including Powell, Halls, Farragut, Alcoa, Seymour, Clinton, Maryville, Oak Ridge, and Sevierville. Fast dispatch runs 7am to 7pm, Sunday through Friday, and most Knoxville addresses get same-day service. For customers in Powell, our gate repair team covers driveway and commercial gates, and for Halls, gate repair is a short run from the core area.
Serving Knoxville, TN – Our Local Coverage Area
We serve Knoxville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in Knoxville
Gate repair is the diagnosis and fixing of anything that stops a gate from opening, closing, or holding position correctly. That covers the gate leaf and hardware, the operator and control board, the safety devices, and the wiring that connects them. It’s the work we do across swing and slide gates, residential and commercial, on the brand already on your property.
Most repairs finish in a single visit, often within a couple of hours. Hinge and roller work is quick; control-board and wiring repairs take longer because the fault has to be traced first. If a part has to be ordered, we tell you the timeline before you commit. We confirm the gate cycles correctly before we leave.
Most gate repairs in Knoxville run $150 to $900 depending on the gate type and the fault. Mechanical repairs sit at the low end, and operator, control-board, and commercial access work sit higher. The estimate is free and written, and the price is agreed before any work starts. Call (866) 361-6964 for an exact quote.
Yes. We service LiftMaster, FAAC, BFT, Mighty Mule, Linear, Viking, Ghost Controls, DoorKing, and Elite systems. That range covers both residential openers and commercial-grade access systems, which most local shops don’t. Tell us the brand when you call and we’ll come prepared.
Yes, same-day service is often available in Knoxville. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. We’re closed on Saturday, so a call that comes in on Saturday is booked into the next opening.
We stand behind our work with a satisfaction guarantee. Wear parts like hinges and rollers are subject to normal use, and we’re clear about what’s covered before we start. Ask about coverage for the specific repair when you get your written estimate.
Clear the driveway on both sides of the gate so the leaf can travel freely and our technician can reach the operator. Note the brand, the model if you can see it on the unit, and exactly what the gate does or doesn’t do. If the gate is stuck open, secure anything exposed until we arrive.
Schedule Your Gate Repair Service in Knoxville Today
A gate that won’t open, won’t close, or won’t hold position is a problem that gets worse with every cycle. Call (866) 361-6964 to schedule a visit. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Our technicians have up to experience on the brand already on your gate, the estimate is free, and the price is agreed before any work starts.
Written by the team at Gate Repair Knoxville.