Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Halls, TN
Gate work in Halls rarely looks like gate work anywhere else. Driveways here run long off Highway 88 and the county roads, many of them gravel, serving farmsteads, manufactured homes, and older single-family houses with detached shops behind them. That means the gates we see are welded steel tube farm gates, chain-link, and custom pipe gates on wooden or steel posts, not ornamental estate systems. West Tennessee’s wet summers and freeze-thaw winters rot those posts and rust the steel, and heavy spring rain on clay-heavy ground throws gates out of plumb. We install gates built for that reality. Call (866) 361-6964 for a free estimate.
Why Halls Homes Are Different
Halls sits in Lauderdale County, unincorporated and rural, and the housing stock tells you why gate work here is its own category. You’ll find older single-family homes, manufactured homes, and farmsteads with detached shops and outbuildings, so the gate at the end of the driveway is usually holding back more than a lawn: trucks, tractors, livestock, equipment. Welded steel tube and custom pipe gates are the norm, mounted on wooden or steel posts set in concrete that has often heaved or rotted at the ground line after years of wet winters and dry summers.
The climate does the rest. Humid subtropical summers rust bare steel and swell wooden posts; freeze-thaw cycles work concrete loose; spring rains saturate the clay-heavy soil until a post shifts and the gate starts dragging on gravel or refusing to latch. A gate that worked all winter can be out of line by April. That’s not a hardware failure, it’s a ground failure, and it changes how we approach installation here: footing depth and drainage matter as much as the gate itself.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Our Main Halls Services
Most calls we get from Halls fall into two groups: a gate that’s stopped working and needs repair, and a gate system that needs to be installed or replaced from scratch. Both are handled by the same technicians.
Gate Repair in Halls
Repair work in Halls is usually about alignment, not parts. A gate that was fine until spring rains loosened its post starts dragging on the gravel, then fails to latch, then gets forced and bends the frame. We straighten frames, reset or replace posts, rehang hinges, and repair latches on welded steel tube, chain-link, and pipe gates. Rust treatment and post rot are part of the conversation on almost every rural driveway, because fixing the gate without fixing the ground under it just means a callback. Our technicians have up to experience with these repairs. For gate-specific repair work in Halls, start with Gate Repair in Halls.

Electric Gate Repair in Halls
Automatic gates on long rural driveways take a beating from farm trucks and equipment, and when the operator quits the gate is either stuck open (a security gap on a property with livestock or equipment) or stuck closed (an access emergency). We work on control boards, operators, loop detectors, safety edges, and wiring, on brands including Mighty Mule, LiftMaster, and FAAC. Power and wiring at a gate are genuinely dangerous, so diagnostics and repairs are handled by trained technicians, not by a homeowner with a multimeter. For automated systems, see Electric Gate Repair in Halls.

Gate Installation in Halls
Installing a gate in Halls means solving for the ground before you solve for the gate. Long gravel driveways off Highway 88 and the surrounding county roads serve farm trucks, trailers, and tractors, so the gate has to be sized, hung, and footed for real weight and real traffic, not a decorative suburban opening. The clay-heavy soil that shifts after spring rains is the same soil your posts sit in, and the humid summers that rust bare steel are the same conditions the finish has to survive. We handle Gate Installation for new driveways and for replacing gates that have finally lost the battle with rot and rust.
Driveway Gate Installation
Signs you need it
Your existing gate posts are leaning, the gate drags on the gravel through most of the year, or the gate you have was never sized for the trucks and trailers now using the driveway.
What it costs in Halls
Driveway gate installation in Halls typically runs from $1,800 to $6,500, depending on gate type, width, and how much post and footing work the ground requires.
How we do it
We measure the opening and the traffic, set new posts to proper footing depth with drainage in mind, hang and align the gate, then test the swing or slide through its full travel before we leave.
Automatic Gate Installation
Signs you need it
You’re tired of getting out to open the gate in the rain, or the driveway is long enough that manual opening has become a daily chore for everyone who uses it.
What it costs in Halls
Automated gate installation typically runs from $3,500 to $9,500, covering the operator, controls, safety devices, and the power run, with the written estimate setting the final figure.
How we do it
We confirm the gate is sound enough to automate, mount and program the operator, install safety edges and loop detectors, run and protect the power and control wiring, then test every cycle and every safety reverse.
What Gate Installation Costs in Halls
| Item | Typical range in Halls |
|---|---|
| New manual driveway gate, installed | $1,800 – $4,500 |
| New automatic driveway gate, installed | $3,500 – $9,500 |
| Gate operator added to an existing gate | $1,400 – $3,800 |
Do you handle the power run and the safety edges?
Yes. Automatic gate installation includes the operator, control wiring, loop detectors, and safety edges, all installed and tested by our technicians. We don’t leave the electrical side for another trade to finish.
Can you install a gate on a long gravel driveway in Halls?
Yes. Long rural driveways are the standard here. We size posts and footings for the soil and traffic, and we’ll tell you upfront if the ground needs work before any gate goes up.
Brands We Service in Halls
We work across nine gate platforms, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, spanning residential openers through commercial access systems. We don’t claim to stock parts locally; we diagnose what’s actually wrong and order what the job needs, so turnaround depends on the part. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Halls, TN
| Service | Typical range in Halls |
|---|---|
| New manual driveway gate, installed | $1,800 – $4,500 |
| New automatic driveway gate, installed | $3,500 – $9,500 |
| Gate operator added to an existing gate | $1,400 – $3,800 |
| Gate repair (frame, hinge, latch, alignment) | $180 – $650 |
| Post reset or replacement | $250 – $900 |
| Electric gate repair (operator, control board) | $220 – $850 |
| Safety edge or loop detector replacement | $200 – $600 |
| Gate operator replacement | $900 – $3,200 |
In Halls, price is driven mostly by the ground: how deep the posts must go, whether old concrete has to come out, and how much rust or rot the frame has. Long driveways also add wiring distance on automatic work. Every job is quoted and agreed before any work starts, so the written estimate is the price.
Neighborhoods We Serve in Halls
We cover Halls and the rural roads around it, including driveways and field entrances off Highway 88 and the county roads that feed into it. Because this is farm and rural-residential country, most of our Halls work is scheduled rather than rushed, and we’ll give you a realistic window when you book. Call (866) 361-6964. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
- Highway 88 corridor
- Halls and the surrounding county roads
- Farmsteads and rural driveways throughout Lauderdale County
- Manufactured home communities and older single-family properties in the Halls area
Service Area – Cities Near Halls
Halls is one of several communities we cover across the region. If you’re outside Halls, we also work in Powell, TN, Knoxville, TN, Clinton, TN, and Oak Ridge, TN. Gate types shift from county to county, from farm gates to ornamental and commercial systems, and we handle all of it. For the wider picture across the region, see Gate Repair Knoxville.
Serving Halls, TN – Our Local Coverage Area
We serve Halls and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
FAQs About Gate Company in Halls
We answer 24/7 and dispatch Sunday through Friday, 7am to 7pm, so most Halls calls are booked into the next available slot, often same-day for repair work. Installation is scheduled after a free measure. Call (866) 361-6964 for a free estimate.
Permit rules vary by county and by whether the gate crosses a public right of way, so check with Lauderdale County before work begins. We’ll tell you what we know about your specific setup during the estimate.
Yes. We work on residential driveways and commercial or multi-access properties alike, including operators, loop detectors, and access control on commercial-grade systems. Call (866) 361-6964 for a free estimate.
What happens when you call
- 1A real person answersNo phone trees. Talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3A background-checked tech heads outLicensed & insured, typically within 60 minutes.
- 4You approve before work beginsNothing starts until you say go.
What Halls Customers Say
"The loop detector under the driveway had failed and residents were stuck holding the button. He traced it, found the break, and had the exit loop reading cars again the same visit."
- Emily Ackerman"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
- Brooke Whitaker"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
- Danika Bryant