Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Installation for Knoxville Homeowners
A gate that won’t close properly, opens on its own, or was sized for a lighter driveway than the one you have is a daily aggravation in a city where driveways climb hills and winters bring hard freezes. We handle gate installation in Knoxville as a dedicated gate job, not a side project between other trades. Our technicians have up to experience and work across LiftMaster, FAAC, BFT, and the residential opener brands most local properties already run. Whether you’re setting a new gate for a home off Northshore or adding access control to a commercial lot, the work is measured, quoted in writing, and scheduled. Call (866) 361-6964 for a free estimate. We answer 24/7. Fast dispatch from 7am to 7pm, Sunday through Friday.
Automatic Gate Installation
Automatic Gate Installation is the design, mounting, and commissioning of a gate that opens and closes on its own through an operator, whether you’re replacing a manual gate that’s become a chore or putting in a new entrance from scratch. Homeowners typically want it once a driveway is long enough that getting out of the car twice a day is genuinely annoying, and property managers want it when vehicle traffic needs to be counted or logged. We size the gate leaf to the operator, not the other way around, and we match the operator to how often the gate actually runs. A typical automatic gate installation in Knoxville runs $3,200-$7,500 depending on gate size, material, and whether a power run already exists. Most installations take one to three days once the gate and operator are on site. The written estimate sets the final price, and we quote it before any work starts.
Sizing the Operator to the Gate
A swing operator rated for a light ornamental leaf will wear out fast on a solid wood gate that catches the wind. We weigh the leaf and check its swing arc before we pick an operator, so the motor is never working harder than it should. That one step prevents most of the callbacks we see on other people’s installs.
Power and Safety Components
If there’s no power at the gate post, running a circuit is a separate, scheduled electrical task that has to happen before commissioning. We set photo eyes, safety edges, and any loop detectors as part of the install. A gate that closes on a car or a person is not finished, no matter how well it swings.
Styles & brands we work with
- Wrought iron
- Wood & steel frame
- Farm & ranch
- Sliding driveway gates
- LiftMaster operators
Gate Installation Services
Gate Installation Services cover everything from a single residential driveway leaf to a multi-access commercial entrance, including fabrication, post setting, mounting hardware, and the operator. Most people reach this point when a gate has rotted, bent, or come loose from failing posts, or when a property needs an entrance it never had. We work both swing and slide designs and handle the site visit before any number is quoted. A typical residential install in Knoxville runs $2,600-$6,800; commercial entrances with multiple access points run higher depending on the number of operators and control hardware. Our technicians have up to experience across the residential and commercial tiers, so both get the same careful measurement. You’ll get a written, itemized price before anything is ordered.
Measuring the Site Before Ordering
Grade, slope, and the soil at the posts decide whether a swing or slide gate is even practical. We measure the opening, check for buried utilities, and note how the ground moves across the entrance. Cutting the gate after it’s delivered is how installs go wrong and cost more.

Residential and Commercial Scope
A single home needs a reliable operator, remote controls, and a keypad. A commercial entrance usually needs loop detectors, an access control panel, and often a separate pedestrian gate. The plan changes with the traffic, so we write it up separately for each job.

Electric Gate Installation
Electric Gate Installation means wiring the operator, controls, and safety devices into your property’s electrical supply and commissioning the whole system so it runs reliably. If your gate is manual and you’re tired of getting out of the car, or the old operator finally failed, this is the job. We mount the operator, run the control wiring, set the limit switches, and test every safety device before we sign off. A typical electric gate install in Knoxville runs $3,000-$7,200, with the figure driven mainly by whether a power run already exists and how many access devices the entry needs. For properties already wired, the job is faster. For a fresh circuit, we schedule the electrical work and the gate work together so neither waits on the other.
Control Board and Wiring
The control board is where most electric gate problems start, so we mount it where it stays dry and is easy to reach. Wiring gets run in conduit, buried to depth, and labeled at the panel. That’s unglamorous work, but it’s what keeps the gate running for years.
Safety Edges and Photo Eyes
Every electric gate needs reversing protection that stops or reopens the leaf on contact or beam interruption. We test each photo eye and safety edge through a full open and close cycle before we finish. If a device fails, the gate stays open until it’s replaced, not closed on a guess.
Driveway Gate Installation
Driveway Gate Installation is building a gate for the specific width, slope, and surface of a driveway, which in Knoxville usually means dealing with a grade change between the street and the house. A gate that crosses a slope can bind, drag, or hang unevenly if it’s mounted level, so we set it to suit the ground rather than forcing the ground to suit the gate. Most homeowners need this when building a new home, adding a fence, or replacing an old gate that never cleared properly. A typical driveway gate in Knoxville runs $2,800-$6,500 for a single swing, and $4,500-$9,000 for a double or a slide with an operator. We quote the price in writing before any work starts, and the written estimate sets the final number.
Handling Slope and Grade
Slope at the entrance is the most common reason a driveway gate sticks or swings open on its own. We check the grade and the driveway surface before selecting the design, swing or slide, and mounting method. Getting that right at the start saves a lot of frustration later.
Materials for Local Weather
Knoxville gets hard freezes in winter and humid summers, which is rough on wood, and it takes a toll on hardware that isn’t rated for the swing count. We recommend materials matched to how much the gate actually moves. A gate that runs a dozen times a day needs sturdier hinges than one that opens twice.
Sliding Gate Installation
Sliding Gate Installation sets a gate that rolls along a track instead of swinging, which is what you want when the driveway is short, the grade is steep, or the gate opening is wide. A slide gate needs clear space alongside the fence line to roll back into, so we check the run before quoting. These gates avoid the wind-catching and side-clearance problems of a swing gate, and they work well on tight residential lots and busy commercial entrances. A typical sliding gate install in Knoxville runs $3,500-$8,500 with an operator, depending on gate width, material, and the track foundation. Every figure is quoted before work starts, and the written estimate is final.
Track and Foundation
A slide gate is only as good as the track it runs on, so we set the track foundation at proper footing depth and check it for level along the full run. A track that settles will pull the gate off line, and a gate off its track can tip or jam. We compact and set the base before the gate ever shows up.
Clearance and Roll-Back
You need enough open fence line for the gate to slide back into without hitting a wall or a parked car. We measure that clearance during the site visit and flag it before the gate is ordered. If there isn’t room, a swing gate or a different design is the honest answer.
Gate Opener Installation
Gate Opener Installation is fitting and commissioning the motor, arm, or underground operator that moves your gate, along with the remotes, keypad, and access devices that let people in. You need it when an existing opener has failed for good, when you’re automating a manual gate, or when the current operator can’t keep up with traffic. We work with LiftMaster, Mighty Mule, and the commercial systems property managers already trust, and we match the opener to the gate instead of forcing a mismatched pairing. A typical gate opener install in Knoxville runs $1,400-$3,800 including the operator and controls, with the price set by the gate size and how many access points the entry needs. We quote in writing before work starts.
Choosing the Right Operator
A residential opener on a light gate is a very different machine from an underground operator on a commercial slide gate. We check the gate weight, the number of daily cycles, and the power available before recommending one. Brand-agnostic diagnostics mean the recommendation follows the job, not what we happen to stock.
Remotes, Keypads, and Access
Most entries need more than one way in, so we set up remotes, a keypad, and any card or intercom access the property calls for. Each device gets tested from the actual distance people will use it. A remote that only works from ten feet is not set up.
Gate Fabrication
Gate Fabrication is building a gate to fit an opening, rather than buying a stock gate and hoping it fits. That matters when the driveway is wider or narrower than standard, when the pitch of the entrance is unusual, or when a property needs a design that matches an existing fence or stone wall. We fabricate swing and slide gates in steel and other materials, sized to your opening and to the operator that will move them. A typical fabricated gate in Knoxville runs $2,400-$6,000 for the gate itself, with operator and install priced separately. We measure on site, quote in writing, and build to the drawing, so what arrives fits what’s already there. Call for a free estimate before anything is ordered.
Custom Sizing and Design
A gate that has to match a particular fence or wall is best built to the opening after measurement, not adapted from a catalog. We take the measurements at the site, work with the material you want, and account for the operator and hinge hardware in the build. That planning is what keeps a custom gate from needing custom fixes later.
Gate Repair Knoxville
Installation and repair work under one provider, so you never coordinate a separate installer and a separate repair tech across the life of the system. When a fabricated gate needs adjusting years later, it’s the same team that takes the call. You can find the repair side of what we do at Gate Repair Knoxville.
Brands We Service
We service LiftMaster equipment and know where it wears out, from limit switches to control boards, and we handle it on both residential and light commercial gates. We also work with Mighty Mule, the entry-level residential opener many homeowners install first, and we know when it’s better to repair than to replace. On the commercial side, we work with FAAC and BFT operators, including underground arms and heavy-duty slide and swing systems that see constant traffic. Our technicians have up to experience across all the platforms we handle, so diagnostics follow the system, not a single brand’s playbook.
The full brand list we work with includes Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule alongside LiftMaster, FAAC, and BFT. That range means a home with a budget residential opener and a commercial lot with a DoorKing access system both get a technician who knows the equipment. We don’t push a replacement you don’t need to sell a particular product line. Whether you have LiftMaster or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- The gate won’t stay closed. A gate that drifts open leaves a driveway exposed, and on a commercial lot that’s a security gap you can’t leave overnight. The cause is usually a failing operator, a worn hinge, or a control board fault that needs a technician to trace.
- The gate won’t open at all. A gate stuck closed is an access problem the moment you need to leave, and it gets worse if a delivery, a school run, or a shift change is waiting on it. We answer 24/7 and can book a same-day visit when the schedule allows.
- The gate reverses for no reason. Reversing on its own usually points to a photo eye out of line, a damaged safety edge, or a control board misreading the signal. Don’t assume it’s fine because it worked yesterday; safety devices fail without warning.
- The gate drags, binds, or jerks. Grinding sounds and uneven movement mean the gate, the track, or the operator is out of alignment. Left alone, that strain wears out hinges and operator gearboxes fast.
- You’re hearing the operator strain. A motor that hums louder than it used to, or trips a breaker, is working harder than it should. It’s a sign the operator is undersized for the gate or the gate is binding, and both get more expensive the longer you wait.
Our Process, Step by Step
- 1
Call and tell us about the gate. We answer 24/7 and get the basics: swing or slide, existing operator or new, residential or commercial. If you already know the brand, tell us; if not, we can identify it on site.
- 2
Free on-site measurement and quote. We check the opening, the grade, the power situation, and the access devices the entry needs. Then we write up the price range and what’s included, so there are no surprises.
- 3
Order the gate and operator. Once you approve, we order the gate, the operator, and the hardware to match. No work starts and nothing gets ordered until the written price is agreed.
- 4
Install and wire. We set the posts and track to proper footing depth, mount the operator, run control wiring in conduit, and set the limits. Installation work is scheduled rather than same-day, because it’s measured, ordered, and planned.
- 5
Test and hand over. We test every remote, keypad, photo eye, and safety edge through a full cycle, then walk you through operation and the safety devices. If a component fails a test, we fix it before we call the job done.
How Much Does Gate Installation Cost in Knoxville?
Gate installation in Knoxville generally runs $2,400 to $9,000 depending on the type of gate and whether an operator is included. A typical automatic swing gate with an operator runs $3,200-$7,500. A driveway slide gate with an operator runs $4,500-$9,000. Gate opener installation alone, on a gate you already have, runs $1,400-$3,800. A custom fabricated gate without the operator runs $2,400-$6,000 for the gate itself. These are typical estimates; the written estimate sets the final price, and we quote it before any work starts.
What moves the price: the gate’s width and material, whether a power circuit already reaches the entrance, the grade of the driveway, how many access devices (remotes, keypads, loop detectors, intercom) the entry needs, and the operator’s cycle rating. A fresh power run and a very wide slide gate are the two biggest cost drivers.
How to avoid overpaying: get the quote in writing with the gate, operator, and hardware itemized separately, and ask whether the price includes the power run and the safety devices. Wire run in conduit, tested safety edges, and posts set to proper footing depth aren’t extras; they’re the base of a working gate. A free estimate lets you compare what’s actually included rather than a single lump figure. Call (866) 361-6964 for a free estimate; estimates are free and there’s no obligation.
Our Service Area Near Knoxville
We handle gate installation and repair across the Knoxville area, including Powell, Halls, Alcoa, Seymour, Clinton, Farragut, Maryville, Oak Ridge, and Sevierville. Most of these are within a short drive of the city, and we schedule visits to fit the job. Call and tell us where you are; we’ll set a visit that works.
Serving Knoxville, TN – Our Local Coverage Area
We serve Knoxville and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Installation in Knoxville
Gate installation is the process of measuring your opening, setting posts and hardware, mounting the gate, and, if it’s automated, fitting and commissioning the operator and safety devices. It covers both a new gate on a bare driveway and a replacement for a failing one. We handle the fabricated gate and the operator together, so you only deal with one provider. Call (866) 361-6964 for a free estimate.
Most residential gate installations take one to three days once the gate and operator are on site, and the lead time before that depends on whether the gate is fabricated to order. A stock gate and opener can go in faster; a custom fabricated gate takes longer to build. We give you a timeline in the written estimate. Call for a free measure and a written price.
A typical gate installation in Knoxville runs $2,400-$9,000 depending on the type of gate and whether an operator is included. An automatic swing gate with an operator typically runs $3,200-$7,500, and a slide gate with an operator runs $4,500-$9,000. Opener-only installation on an existing gate runs $1,400-$3,800. Call (866) 361-6964 for an exact quote – estimates are free.
Yes, we service LiftMaster, FAAC, BFT, and Mighty Mule, along with Linear, Viking, Ghost Controls, DoorKing, and Elite. We work on both the residential openers and the commercial access systems, so a home and a commercial lot both get a technician who knows the equipment. Brand-agnostic diagnostics mean the recommendation follows what the system needs. Call and tell us your brand.
Same-day service is available for repairs when the schedule allows, but gate installation is scheduled work, so it’s measured, ordered, and priced before the install date. For a repair on a gate that’s stuck or won’t secure, we answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (866) 361-6964.
We back our work and stand behind the installation, and we’ll walk you through the coverage on the gate, the operator, and the labor when we hand over the job. The exact terms are set out in your written estimate so you know what’s covered before work starts. Ask us at the estimate and we’ll explain it plainly. Call (866) 361-6964.
Clear the entrance so we have room to work, and let us know if you know the gate brand or have any fence or property plans. If you have photos of the driveway and the entrance, they help us plan before the site visit. Have the power situation sorted if a new circuit is needed; we’ll schedule the power run and the gate together. Call for a free measure and a written price.
Schedule Your Gate Installation Service in Knoxville Today
Call (866) 361-6964 to set up a free estimate for your gate installation in Knoxville. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday. We’ll measure the opening, confirm the plan, and put the price in writing before any work starts. No obligation, no surprises, just an honest quote.
Written by the team at Gate Repair Knoxville.